Here is a Receiver Schematic that works on FM and AM band. A FM receiver can be built easily using only a single chip CXA1019. This circuit has been following with a PCB.

FM/AM receiver operates on a DC voltage of 6 volts or uses four pieces of AA batteries. For other component specifications can be seen on the list of components on the bottom of the article.

CXA1019 FM receiver schematic is quite easy to build because it uses a small number of components with low current consumption is 5.3 mA at 3V Vcc. However, it’s an AF amplifier with large output of about 500mW at 8? load impedance.

FM Receiver Schematic – PCB

CXA1019 FM Receiver Schematic

CXA1019 FM Receiver-PCB Top

PCB Dimension : width=7.95 cm, Height=4.90 cm

CXA1019 FM Receiver-PCB Bottom

CXA1019 FM Receiver Part List

CXA1019 FM Receiver Part List

XCA1019 FM Receiver Parts

For those who are beginners this is an exciting electronic project to add to the experience, namely how to make an FM/AM radio using a receiver schematic.

See also: Emergency Radio Circuit - Transistor FM Receiver Circuit

Here’s simple FM receiver circuit for a simple super-regenerative FM radio. It is sensitive, selective, and has enough audio drive for an earphone. These designs generally have low component counts, however the design or my construction have been far from simple.

FM Receiver Circuit Diagram

Because the FM receiver is a super-regenerative design, component layout can be very important. The tuning capacitor, C3, has three leads. Only the outer two leads are used; the middle lead of C3 is not connected. Arrange L1 fairly close to C3, but keep it away from where your hand will be. If your hand is too close to L1 while you tune the FM receiver, it will make tuning very difficult.

One Transistor FM Receiver Circuit Schematic

FM Receiver Circuit – Winding L1

L1 sets the frequency of the radio, acts as the antenna of the FM receiver, and is the primary adjustment for super-regeneration. Although it has many important jobs, it is easy to construct. Get any cylindrical object that is just under 1/2 inch (13 mm) in diameter. I used a thick pencil from my son’s grade school class, but a magic marker or large drill bit work just fine. #20 bare solid wire works the best, but any wire that holds its shape will do. Wind 6 turns tightly, side-by-side, on the cylinder, then slip the wire off.

Spread the windings apart from each other so the whole coil is just under an inch (2.5 cm) long. Find the midpoint and solder a small wire for C2 there. Mount the ends of the wire on your circuit board keeping some clearance between the coil and the FM receiver circuit board.

FM Receiver

FM Receiver Circuit – A tuning knob for C3

C3 does not come with a knob and I have not found a source. A knob is important to keep your hand away from the capacitor and coil when you tune in stations. The solution is to use a #4 nylon screw. Twist the nylon screw into the threads of the C3 tuning handle. The #4 screw is the wrong thread pitch and will jam (bind) in the threads. This is what you want to happen. Tighten the screw just enough so it stays put as you tune the capacitor. The resulting arrangement works quite well.

FM Receiver Circuit – Adjustment

If the radio is wired correctly, there are three possible things you can hear when you turn it on: 1) a radio station, 2) a rushing noise, 3) a squeal, and 4) nothing. If you got a radio station, you are in good shape. Use another FM rceiver to see where you are on the FM band. You can change the tuning range of C3 by squeezing L1 or change C1. If you hear a rushing noise, you will probably be able to tune in a station.

Try the tuning control and see what you get. If you hear a squeal or hear nothing, then the circuit is oscillating too little or too much. Try spreading or compressing L1. Double check your connections. If you don’t make any progress, then you need to change R4. Replace R4 with a 20K or larger potentiometer (up to 50K). A trimmer potentiometer is best. Adjust R4 until you can reliably tune in stations. Once the circuit is working, you can remove the potentiometer, measure its value, and replace it with a fixed resistor. Some people might want to build the set from the start with a trimmer potentiometer in place (e.g., Mouser 569-72PM-25K).  Source: Build A One Transistor FM Receiver.

See also: Transistor FM Transmitter MP3 Circuit – VHF Radio FM Transmitter Circuit